Heute habe ich an einer SUN/Oracle M9000 eine I/O-Unit ausgetauscht. Diese Unit beinhaltet alles was die Hardwaredomain so für I/O braucht… da wäre PCIe, SAS, bla… in dem Fall meine FC-HBAs und die Bootplatten.

Der Wechsel der kompletten Unit erfolgt in drei Schritten. Zuerst melden wir uns am XSCF an.
XSCF> replacefru
———————————————————————-
Maintenance/Replacement Menu
Please select a type of FRU to be replaced.
Notice)
There are some FRU(s) under maintenance.
This situation may be due to a previously interrupted
maintenance procedure.
Please select the following FRU(s) first.
CMU#0 ,IOU#0
1. CMU/IOU (CPU Memory Board Unit/IO Unit)
2. FAN (Fan Unit)
3. PSU (Power Supply Unit)
4. XSCFU (Extended System Control Facility Unit)
———————————————————————-
Select [1-4|c:cancel] :1
———————————————————————-
Maintenance/Replacement Menu
Please select whether to replace a CMU only, an IOU only,
or both a CMU and an IOU.
1. Replace CMU only.
2. Replace IOU only.
3. Replace both CMU and IOU.
———————————————————————-
Select [1-3|b:back] :2
———————————————————————-
Maintenance/Replacement Menu
Please select an IOU to be replaced.
DomainID
No. FRU XSB#0 XSB#1 XSB#2 XSB#3 Power Status
— ————- ———————– —– —————
1. IOU#0 1 1 1 1 Off Degraded
2. IOU#1 0 0 0 0 On Not installed
3. IOU#2 0 0 0 0 On Normal
4. IOU#3 0 0 0 0 On Not installed
5. IOU#4 — — — — — Not installed
6. IOU#5 — — — — — Not installed
7. IOU#6 — — — — — Not installed
8. IOU#7 — — — — — Not installed
———————————————————————-
Select [1-8|b:back] :1
———————————————————————-
Maintenance/Replacement Menu
Status of the selected FRU.
FRU Status
————- ——–
IOU#0 Degraded
———————————————————————-
You are about to replace IOU#0.
Do you want to continue?[r:replace|c:cancel] :r
Please confirm the Ready LED is not lit and that the Check LED is
blinking.
If this is the case, please replace IOU#0.
After replacement has been completed, please select[f:finish] :f
Hier im Beispiel geht es um die IOU#0
Nach der Auswahl des Replacetasks vir replacefru kommt der eigentliche Hardwaretausch.
- 1. CMU/IOU
- 2. Replace IOU only.
- 1. IOU#0 1 1 1 1 Off Degraded
Im dritten Schritt von replacefru wird auch nochmal angezeigt, dass die Komponente als “degraded” geführt wird.
Der mit “r” gestarteter Replaceprozess gibt noch zwei letzte Anweisungen und dann kann die IO-Unit sauber getauscht werden.
Nachden die neue Unit sauber verbaut ist, kann LAN, FC und sonstiges wieder angeklemmt und mit “f” der Replaceprozess abgeschlossen werden.
Jetzt sollte sich das XSCF melden und die neue Komponente untersuchen wollen:
To ensure correct operation, diagnostic tests should be run on
IOU#0.[d:diagnose|s:skip] :d
Diagnostic tests for IOU#0 have started.
[This operation may take up to 60 minute(s)]
(progress scale reported in seconds)
0….. 30….. 60….. 90….. 120….. 150….. 180….. 210….done
———————————————————————-
Maintenance/Replacement Menu
Status of the selected FRU.
FRU Status
————- ——–
IOU#0 Normal
———————————————————————-
The replacement of IOU#0 has completed normally.[f:finish] :f
Wenn auch das sauber durchlief landen wir wieder im Hauptschirm von replacefru und können mit “c” beenden.
Jetzt sollte die Domain wieder hochkommen und aus dem “OK” Prompt sauber booten.